I didn´t like the NE555, but this was just a stereotype...
I´ve build this NE555 sawtooth(!) generator for everyone who has problems with it, and I have to say it works fine.
DC Offset adjustable 0...24V
AC (sawtooth) amplitude adjustable 1...7V peak-peak.
So it will work with the POS1060...
Tomorrow i add pictures of the oscilloscope.
[...]
For a jammer you need just a sawtooth generator, which tunes a voltage controlled oscillator (like POS1060 or MAX2622) continusly from lower frequencies to higher frequencies.
-----------------------------
If you want to jam the complete the gsm downlink band (920-960MHz), you have to disturb it with a carrier that sweeps around, because the bandwith of our carrier is too small to cover the whole band. To get the vco sweeping, we have to feed it with a changing signal, the best signal for this task is sawtooth signal.
-------------------
The POS1060 is a vco that produces frequencies from 750...1060MHz.
The tuning voltage is 1...20V.
So we may say: 750MHz comes out we the tuning voltage is 1V,
and 1060MHz comes out when the tuning voltage is 20V.
So what tuning range do we need for 920-950MHz?
Calculate it, and you get 10,9...13.55V ---> or better 10...15V to be sure
We have to adjust the sawtooth generator to let him produce that voltage range we need.
I´ve made 3 pictures of my sawtooth generator, for example:
http://homepages.compuserve.de/richardkotte/1.jpg
What we see: 12V DC and 4V AC=> 10...14V
This waveform would be suitable for our jammer!!
http://homepages.compuserve.de/richardkotte/2.jpg
1,5...4,5V, just for example
http://homepages.compuserve.de/richardkotte/3.jpg
17,5V DC and 5V AC (noticed the voltage button at the oscilloscope?), so we get 15...20V.
At all these pictures we have a sweep frequency of 12,5kHz.
That means that the vco moves 12500 times per second from the lower to the higher frequency.
The vco sweeps over the gsm band, and so gsm will be jammed...
Any questions?
Hi friend
I build you sawtooth . work well. But I am again unable to tune the Pos1060 .
Vcc= 8 and 10V
In Tune PIN= 15v DC AND 4v peck to peck
With 3khz frequency
Not showing anting for output
What you is is wrong
I GDN pin 7 and show all other GDN may be interconnected
As POS1060 datasheet saying it need 30um and I give it 1.4um ( is that problem)
Please reply I only have two days more to submit my project
Hallo Freund
errichte ich Sie Sägezahn. Arbeit Brunnen. Aber ich bin wieder nicht imstande, das Pos1060 abzustimmen. Vcc = 8 und 10V Im Melodie STIFT = in DC 15v UND in 4v peck peck Mit Frequenz 3khz Zeigen nicht des Antings für Ausgang Was Sie sind falscher I GDN Stift 7 sind und stellen Sie dar, daß weitere ganzes GDN zusammengeschaltet werden kann Wie das datasheet POS1060, das es Notwendigkeit 30um und ich sagt, sie geben, 1.4um (ist dieses Problem) Bitte Antwort habe ich nur zwei Tage, mehr, zum meines Projektes einzureichen
I don´t know what is wrong with your circuit.
Can you please draw a diagram or take a photo of your current circuit?
>>Not showing anting for output
How have you measured this??
------------
Besides:
Don´t translate the text.
That german is much harder to read than your english
hi
i am working on test circuit with sawtooth genrator and POS1060 giving ouput is -ve tomarow i will upload my picture,s
yes giving -0.5 moving upto +0 the again oning into -ve here is the picture of output .
what do you think about GDn problem do i need to GDN all pin when all are interconnedted
No, imgemini, this is definitively NOT the output signal of the POS1060.
In that case you would have an oscilloscope with a bandwith of at least 4 GHz . Such oscilloscopes don´t exist
Maybe a 500MHz oscilloscope can show the signal, but those are very expensive... ~6000-8000€
---
Perhaps this signal comes from interferences?
---------
You can put Gnd at Pins 3,4,5,6,7. That´s ok.
then why its showing -ve in DC
is POS1060 and sawtooth genrator are eoungh for jam 1 meter ?
tomarow i will uplaod picture of step by step what i m doing and plesae see that post to tell me where i am worng
>>is POS1060 and sawtooth genrator are eoungh for jam 1 meter ?
Yes.
Solder a short antenna to the vco output (a wire with the lengh of 8cm)
sorry i am asking too much qustion but as you know its my project and have to submit within two days
why my pos1060 showing ouput is -ve DC ......its normal or there is something wrong . i am sure you also face this problem when u work on MAX2623 .
what do u think